BMW I-level in FRM Problem solved by Ediabas Tool32

Problem:

I need to change I-Level in FRM3 module.

I have problem with BMW ICOM ISTA-P because i have wrong I-Level in used FRM module.
I was looking for change I-level in Ediabas Tool32 and frm3.prg, but i didn’t find right parameter for change I-level in FRM3.

I have problem with reading I-Level from cas and FRM. Please look at screen. I-Level in CAS is empty, I-level in FRM is unreadable.

I-Level in E89.prg is perfect and readable.

Could somebody write me what to do step by step?

Final solution from BMW expert:

I-Level in your CAS and FRM is identical:
00 ED = E89X-07-12-515
23 DC = E89X-09-03-520

You can change it by job I_STUFE_SCHREIBEN in E89X.PRG
This job writes I-Level to both ecu CAS&FRM

With args E89X-07-12-515;E89X-09-03-520;E89X-09-03-520 job writes your current I-Level as example

Result:
Took the advice and it worked perfect. Hope it helps.

http://obd365.edublogs.org/2017/03/29/change-bmw-i-level-in-frm3-by-ediabas-tool32/

How to Change BMW F10 Manufacturing Date via E-sys

BMW F-series Zeitkriterium or manufacturing date is an important part of most retrofits that enables the use of BMW ENET cable E-sys to recode a module in order to activate the retrofit.

For example some F10 models came with halogen lights and most owners want to retrofit the LCI xenon headlights for better looks and visibility. The DRL is also very weak on halogen headlights and that ruins the way the car looks compared to the xenon equipped ones.

In this tutorial we will show you how to do it step by step.


Connect to e-sys F-series coding software and choose your chassis


Read FA and activate FA


Click on Save and give the file any name you wish, then click on Edit. Right click on the FA and click Calculate FP.



Edit the Zeitkriterium value accordingly to your needs

Calculate FP again then save

Go to the VCM tab, load the file and calculate FP again

Select VCM Master and Write FA FP

Now that the FA FP has been written to the car you can go ahead and recode your module by going back to the Expert Mode Coding tab, Read SVT to see the modules list, right click on the module name (Ex: FRM) and click on “Code”. Wait for the process to finish and you`re done!

http://www.obdii365.com/wholesale/bmw-enet-interface-cable-e-sys-icom-coding-f-series.html

How to code RDC antenna on BMW F25 via ICOM E-sys

Problem：
I recently replaced the RDC antenna on my X3 and it needs to be encoded to work. I currently have BMW ICOM A2 ISTA+ and E-sys with a BMW ENET cable.  I've played with ESYS and got it working, but I'm not sure if flashing the RDC will encode the antenna. Then I took the expert advice to code but not flash with Esys in order to code the module.

Final solution:

Got it done finally. For anyone else in the same boat with a corroded antenna. The RDC antenna on the F25 X3 is just behind the rear passenger wheel. It takes about 5 seconds to disconnect the old one and replace it with a new one. Then it needs to be encoded. Using BMW ENET Esys F-series coding software:

Once connected : -

Expert Mode-Coding

Read FA

Activate FA

Read SVT

Select the 'RDC' ECU

Detect CAFD for SWE

Choose the CAFD you want

Click Code

So basically it's injecting a CAFD file into the module since there wasn't one before.

How to retrofit Cruise Control for BMW F30 F20

This BMW Cruise Control retrofit DIY guide is for F20 or F30 with LIM function only mainly non-US car. The DIY will require you to replace multifunction steering wheel switch and VO Code the car.




What does this DIY do?

Replace and code multifunction steering-wheel switch from LIM function to dynamic cruise control capability on BMW F20 or F30. This will allow the car to have dynamic cruise control capability. The set speed can be selected from 30 km/h to 180 km/h: in convenient steps of 10 or fine steps of 1. The set speed is displayed on the instrument panel via speedo dial and briefly on information display.



Dynamic Cruise Control Dynamic cruise control is an electronic cruise control system with an extra braking function. This also includes the Curve Speed Limiter that reduces the speed in curves for comfortable lateral acceleration. At the end of the curve the car accelerates and resumes the original speed. The driver can change this in increments of 1 or 10 km/h. Acceleration and deceleration in two dynamic settings can be controlled by manipulating the lever on the steering.


Brief component description:
Multifunction steering-wheel switch

The multifunction steering wheel contains a horn switch and airbag plus, depending on the model, buttons for controlling the radio, telephone and cruise control. The buttons are split between 2 switch blocks; left and right.

Functional description

The left multifunction steering wheel switch block is directly connected to the right one via a plug connection. This means that all the button signals in the left multifunction steering wheel switch block are detected and digitised in the electronics of the right switch block.

The right multifunction steering wheel switch block sends the signals via the local interconnect network bus to the steering column switch cluster. The steering column switch cluster is the data interface between the local interconnect network bus and FlexRay. All button signals are sent as FlexRay messages.

The right multifunction steering wheel switch block is directly connected to the left one via a ribbon cable.

What is this DIY?

This DIY will guide you on how to change/code the multifunction steering-wheel switch with cruise control function. The bimmer can be either F20/F30 series with automatic air condition.


Part required:

BMW OEM Multi steering-wheel switch

Note the different in the trim piece highlighted by red arrow.

Leather steering wheel


Sport leather steering wheel


Tools required:

1. Flat head screw driver

2. Torx screwdriver T10, T20


3. Computer with esys installed

4. BMW ENET cable (Ethernet to OBDII) usb interface

5. ESD strap


6. Wrench 10 mm


Installation Instruction for Multifunction Steering Wheel Swtich:

There are two ways to remove air bag. I recommend to remove air bag using the below method as it is easier plus it will not leave any mark on the steering wheel. The BMW method is in the appendix, if you desire to do that way. The toughest part of this DIY is getting the air bag out.

1. Disconnect negative battery terminal.

a. This will add safety from unintentional air bag deployment during removal.

Loosen nut (1).

Important!

Do not under any circumstances use force to pull off negative terminal.

Pull off battery earth lead with IBS in an upwards direction, place to one side and secure.

b. Ground your body with car body with ESD strap (if you have one for extra protection)

2. Removing upper section of steering column shroud

Move steering column in "bottom" and "extended" position.

Pull steering column gap cover up carefully and clip out gap cover.

Pull steering column shroud (1) up.

Clip steering column gap cover (1) out of steering column shroud upper section.

Important!

Risk of damage!

Carefully pull steering column shroud upper section (1) upward at rear and clip out

3. Remove lower steering shroud

Press retaining lugs outwards a little and unclip steering column shroud downwards.

Installation note:

Align steering column shroud by means of retaining lugs to steering column and press up as far as it will go.

Press steering column shroud on both sides together a little and then press upwards completely until retaining lugs snap into place.

Check installation position, correct if necessary.

Tilt steering column shroud in downward direction.

If necessary, unlock plug connection (1) on steering column adjustment switch and (2) emergency starting aerial and disconnect.

Remove lower section of steering column shroud.

4. Turn steering 90 degrees to as illustrated below



5. Look back to the steering wheel from behind underneath steering column for the air bag hook as the picture below and use flat head screw driver to pry the hook and pull the air bag up on same side. Once the air bag is release continuing on the other side above the steering column to get the air bag release from both hooks. After remove airbag turns steering back to normal position.


6. Disconnect airbag and multifunction steering switch electrical connectors from the steering wheel.



7. Remove the air bag and put it in an open space with BMW logo facing up.



8. Use Torx screw driver to loosen two screws to release the multifunction steering switch and trim from steering wheels.

9. Use Torx screw driver to release multifunction steering switch from the trim pieces (4 screws) and replace with new multifunction steering switch. (Need to transfer one electrical connector from the old switch to the new multifunction switch.)



10. Reinstall trim piece to steering wheel and route the wire back to steering wheel.


11. Reconnect the connectors for multifunction switch and air bag and install air bag back by pushing it in until you hear a snap. Check to make sure that air bag is secured firmly.

12. Assemble back the steering column shroud and aerial.

13. Reinstall the steering gap cover.


14. Move steering column to the normal driving position.

15. Reconnect negative terminal.

16. Press start and check the followings:

a. Illumination lights on multifunction steering switch

b. Check the audio control

c. Press horn to check

d. Check for any fault from the instrument panel. Should be none!

17. Start coding




Coding:

Before you do this coding you must already know how to do coding, please search Google

on how to do or where to get the BMW ENET cable and E-sys software. I only let you know the step and ECU to do

FA coding

FA Coding:

1. Launch esys and connect to your car

2. Select expert mode

3. Read and activate FA (add option 544)

4. Read SVT

5. Select and code the following ECU

a. FEM

b. ICM

c. KOMBI



6. If you want “LIM” function, you will need to do FDL coding per the table below. This will

allow “SET” button to act like “LIM” button so that you get both LIM and Cruise control functions.



Testing:

1. Start the car and drive away

2. Once on an open road and the speed is greater than 30 km/h press button to turn on cruise control. The cruise indicator should be lit in the instrument cluster.


3. Press “Set” to set cruising speed then let go gas pedal, if the car can maintain the speed you all done.


4. Fine a bridge/slope and check whether the brake is applied when going down to maintain speed.

5. You all set! Consult owner manual for full detail of cruise operating procedure and precaution.

Appendix:

Removing and installing/replacing airbag unit

Warning!

Observe the following instructions to avoid any risk of injury by the airbag unit.

-Comply with safety regulations for handling components with gas generators.

-Do not exert any force on the airbag unit.

-Use only specified tools for releasing the airbag unit.

Note: Incorrect handling may result in triggering of the airbag unit and thereby cause serious injury

Necessary preliminary tasks:

 Disconnect battery earth lead



Insert Torx screwdriver T20 (1) vertically into the concealed opening until limit position (2) can be felt.

Pull Torx screwdriver (1) approx. 2-3 mm out of opening. Press screwdriver handle towards middle of steering wheel and simultaneously slide into opening to position Torx screwdriver behind retaining spring bracket (refer to graphic below)



Press retaining spring bracket (1) of airbag unit inwards and simultaneously pull airbag unit upwards until it unlocks.

Repeat procedure on other side.

Installation note:

Snap airbag unit with uniform pressing force plane-parallel in direction of steering column shaft into steering wheel.

Warning!

Danger of injury!

The airbag unit may only be set down with the airbag itself facing up.



Tilt airbag unit forwards.

Disconnect plug connections (1) and remove airbag unit.

Installation note:

Make sure electrical leads are correctly positioned.

Done! Enjoy coding. 

How to use INPA for BMW F series coding

Yes, INPA software works with BMW Fxx Chassis, so long as you have the Fxx .IPO files installed.

It will use whatever interface you have defined in EDIABAS.ini, so BMW ENET cable is fine. Also, ICOM A2 is definitely ok.

Here is my INPA 5.06 with Fxx Scripts:

INPA is not updateable with SP=Daten as it uses only the .PRG files in EDIABAS and its own .iPO files.

Here is a full INPA with F and E series for you to download, but no one holds the responsibility for what you will do.

If you don’t wanna take any risk with INPA K+DCAN, here is a tested version for you:

http://www.obdii365.com/wholesale/bmw-inpa-k-can-with-ft232rq-chip.html

Download full INPA on Mega: (on your own risk)

https://mega.nz/#F!atxDATqT!r6SO9Wu75GuDJmpbTTO48Q

BMW Standard Tools 212 - Install First

• Includes (EDIABAS v.7.30, Tool32 v.4.03, INPA v.5.06, WinKFP v.5.31 & NCS Expert v.4.01).

INPA_Fxx_v.2 - Install Second

• Copy INPA_Fxx_v.2 folder to C:\EC-Apps\INPA_Fxx_v.2 and EDIABAS to C:\EDIABAS overriding existing EDIABAS Folder.
• Run INPALOAD.exe from INPA_Fxx_v.2 BIN folder (C:\EC-Apps\INPA_Fxx_v.2\BIN\INPALOAD.exe).
• Note: DISABLE WINDOWS FIREWALL ANY ANY VIRUS SOFTWARE.
• Note: For Exx connection, you will need to change EDIABAS.ini file to "INTERFACE = STD:OBD" and edit OBD.ini Com Port settings accordingly to match you PC's Com Port settings.

The quick diagnose with inpa is much easier and faster than ista/d.... and also for zb-numbers to find...

Files for reference:

BMW E F series coding options available in INPA & E-SYS

BMW INPA 6.4.3 & 5.0.6 & 5.0.2 Free Download

How to choose correct .PRG file in BMW Ediabas Tools32

Which .prg file should you choose for Fxx Jobs in Tool32? This is a short guide of how & which .PRG file to load into Ediabas Tool32 based on your current car.

Disclaimer:  The write-up was made by a Swiss BMW expert. Try at your risk.
Tool needed:

BMW INPA K+DCAN USB cable

INPA & the EDIABAS package which includes Tool32. Search the obdii365 official blog to get some free download resources.

Process:
1. Start BMW INPA software by right-clicking INPALOAD.exe file and selecting ‘Run as administrator’. Load Inpa software.(Fig. 1).

2. Select your relevant Fxx car. I.e F10, press F3.
3. The Script selection window will appear. Select the 1st option on the right – FUNCTIONAL JOBS (Fig. 2).

4. The Select series (Baureihenauswahl) window will appear. Select F1 (Fig. 3).

5. The Job main menu will appear. Select F2 – Identifikation (Fig. 4).

6. Here you can see the result of my car (Fig. 5). Note I have highlighted in yellow the SGBD column. This is the SGBD name and the .PRG file name that you will need to open in Tool32 for working on your modules.

7. Start Tool32 by right-clicking tool32.exe file and selecting ‘Run as administrator’. Tool32 should load.
8. Select File->Load SGBD, Group file.
9. Browse to the EDIABAS\ECU folder, and search for the file name based on the listed yellow column entry. In this example, I’m loading the AIRBAG module file, named ACSM3.PRG (Fig. 6).

10. Once loaded, You will see on the left a list of Jobs available for your module. I have launched the fs_lesen job which is to read the fault memory either double-clicking on it or by selecting it & pressing F5. The Job Results will appear in the window below (Fig. 7).

Please be careful with running Jobs in Ediabas Tool32.

Some Jobs will literally wipe your ECU to a point that only the dealer or even worse – BMW Munich can recover, and to state that it wasn’t your fault will be difficult..

Some wording might not have the context you would expect so research jobs with words like: Initialisierung, Reset, Sperren, Default or Loeschen before you launch them.

In the context of Fault Memory, the Job to clear it is ‘fs_loeschen’.

Hope this helps. Would be great if someone can follow-up with similar instructions for Exx series.

http://blog.obdii365.com/2017/02/08/select-the-correct-prg-file-in-ediabas-for-f-series/

www.autelsale.com

Free ICOM Rheingold 4.03.31 ISTA-P 3.60.4.000 on Mega

Here is customer share the newest version of BMW ICOM A2 Rheingold 4.03.31+SDP 4.03.30+ISTA-P 3.60.4.000, thanks to beemerboy88 and spider80, good luck and enjoy it on your own risk!

Standalone versions of ISTA-D and ISTA-P.

SQLiteDBs 4.03.30, including RU, EN, DE, OTHER.

Free download link(Mega)

https://mega.nz/#!3c8TjLiL!YlVBaE2dImN8p6zAtL54MTzVyqOvLsUi58qT0VHw4ZM

Required interfaces of BMW Rheingold 4.03.31:

BMW ICOM A2

BMW ICOM A3

BMW ICOM Next

BMW INPA K+DCAN USB cable or BMW ENET cable (need special setting)

For unpack archives use 7-zip 16.04 or higher.

All installed and ready to work.
Instructions for installation, configuration and solution of possible errors, is located in the Tools folder (FAQ-RU.pdf and FAQ-EN.pdf).

Read FAQs carefully in Tools folder before ask the questions !!!
ISTA-P – 112 GB
Service Data (SDP) – 70 GB

What’s included in torrent:

http://blog.obdii365.com/2017/02/04/bmw-icom-rheingold-4-03-31-standalone-on-torrent/